Home / Blog / How-To
Audio Tests

How to Test Your Headphones on iPhone With Test Tones

Illustration of an equaliser panel with ten sliders, titled “Test your headphones”

A frequency sweep finds rattles, pink noise shows balance, and band tones narrow a problem to one region, all by ear and at low volume.

A rattle on bass notes, one earbud quieter than the other, a second-hand pair you are not sure about. Most headphone worries come down to one question: is it the headphones, the phone, or the recording?

Music is a poor way to answer it, because you never know exactly how a track should sound. A test tone has one known pitch and noise a known spread, so anything extra is coming from somewhere else.

Here is how to test headphones on iPhone in ten minutes, by ear, with the Audio Tests in Volume Booster: Bass Boost EQ, plus one setting built into iOS. It will not give you a measurement. It will tell you where to look.

Before you test headphones on iPhone: keep it quiet

Find a quiet room, because background noise masks faint buzzes. Set the volume lower than you would play music and raise it only until the signal is clear. Do not add boost or EQ either. You want to hear the headphones, not your settings.

With earbuds, check the tips are seated and the right size, because a poor seal loses bass and sounds like a fault. With the phone speaker, hold the phone rather than resting it on a table, so you are not hearing the furniture.

Quiet is enough

None of these tests needs to be loud: a moderate level is enough to show most rattles, so there is no reason to push it. Sustained loud tones and noise are tiring, ultra-high tones can be uncomfortable, and holding a loud tone can damage a small driver. The safe listening guide covers what a sensible level looks like.

The frequency sweep: rattles, buzzes and dropouts

Start with the sweep, a single tone that glides through the frequency range. It finds faults that only appear at certain pitches. Listen for three things:

  • A rattle or buzz that appears at one point and fades as the tone moves on. Something is vibrating in sympathy: a loose part, a damaged driver or, on the phone speaker, a case or loose button.
  • A dropout, where the tone thins out or vanishes for a stretch, then returns. A gentle fade at the very bottom and top of the range is normal. A hole in the middle is not.
  • Crackle or distortion that follows the tone. If it is on one side only, that side is the suspect.

Run it twice. A rattle at the same point both times is worth chasing, though it could still be the case, phone or source; on a wired pair, crackle or cut-outs that change when you move the cable suggest a loose connection or a damaged cable. If everything you play distorts, not just the sweep, fixing distorted audio covers causes in the source and settings.

Follow along in Volume Booster: Bass Boost EQ

Free on the App Store for iPhone and iPad.

Download on the
App Store

Pink noise and white noise: balance and tone

Noise plays every frequency at once, so it suits judging balance and character.

Pink noise has equal energy per octave, which is closer to how the ear groups pitch, so it sounds balanced and even. White noise has equal energy per frequency. Each octave up holds twice as many frequencies as the one below, so most of its energy lands in the treble, and it sounds bright and hissy.

Use pink noise as your reference:

  • Position. With a healthy pair, the noise sounds evenly balanced between your ears. If it leans to one side, one earpiece is quieter or duller.
  • Character. Is it roughly even, or does one region stand out: a boomy low end, a honky middle, a sharp top? A muffled, dull sound can mean a blocked mesh.

Then try white noise briefly: its extra treble exposes a missing or harsh top end. Keep it short, as it is bright and tiring.

A clean pair that just sounds bright or bass-light needs EQ settings, not repair.

The bass, midrange and treble tones

Once the sweep and noise have pointed at a region, the band tones let you sit on it. What each EQ band does explains each region.

  • Bass. On headphones it should sound clean and steady; a buzz or flutter at a moderate level can point to a damaged driver or a loose part. On the built-in speaker, faint bass is normal: phone speakers are too small to reproduce deep bass.
  • Midrange. Where voices sit. Distortion here is unusual and worth taking seriously.
  • Treble. It should sound clear, not scratchy. A duller tone in one ear can mean debris in that side's mesh, or a poor fit on that side.
  • Ultra-high. Keep it brief and quiet. Hearing it only faintly, or not at all, is common because sensitivity to the highest tones fades with age, and it is not in itself a fault.

Checking each side with the Balance slider

To hear each side on its own, use iOS itself. Go to Settings > Accessibility > Audio & Visual and find Balance, with L at one end and R at the other.

Play pink noise and drag the slider fully to L, then fully to R, listening for any difference in loudness or character.

If the slider was already off centre, that alone explains a quiet side. Put it back in the centre when you finish, because it applies to everything the phone plays.

What a listening test can and cannot tell you

This is a listening check, not a measurement. There is no calibrated microphone, your two ears are not identical, and what you hear depends on fit, volume and the room.

It finds plain faults: a rattle, a dead or quieter side, a hole in the sweep, a muffled earpiece. It cannot chart a frequency response or prove where in the chain a fault sits. For that, change one thing at a time:

  1. Another pair on the same phone. If the fault disappears, it is the headphones. If it stays, look at the phone, adapter or source.
  2. The same pair on another device. If the fault follows the headphones, that confirms it.
  3. Another recording. A fault in one file only is in the file.

The Hearing control in Control Center shows a headphone level meter, which tells you how loud your audio is, not whether anything is wrong. Apple's Hearing Test checks your hearing, not your headphones.

Phone speaker quiet in every app? See fixing quiet iPhone speakers, or the muffled-after-water guide if it got wet.

Quick answers

Why can't I hear the ultra-high tone?

Sensitivity to the highest tones fades with age, so this is normal, not in itself a fault. Do not turn it up to compensate.

Is pink noise or white noise better for testing?

Pink noise, for most purposes. It sounds balanced, so left-right and tonal differences are easy to judge. White noise works as a brief treble check, but it is bright and fatiguing.

Can a test tone damage my headphones?

It is very unlikely at a sensible level for a short test. The risk is holding a loud, sustained tone on a small driver, or adding boost on top.

Is this the same as a hearing test?

No. These signals check whether your speakers or headphones reproduce sound cleanly. They say nothing reliable about your hearing; for that, see an audiologist.

Where to get it

The Audio Tests are part of Volume Booster: Bass Boost EQ: a frequency sweep, white and pink noise, and bass, midrange, treble and ultra-high tones, all played inside the app.

Start quiet, and raise the level only as far as you need to hear each tone clearly.

Get Volume Booster: Bass Boost EQ free

Free to download on the App Store — wallpapers, keyboards, AI photo tools and more.

Download on the
App Store